







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Trusted Windows & Doors for Dallas Homeowners
Dallas weather is hard on openings. Summer sun pushes exterior surfaces past 140°F, then a spring hailstorm hits the same glass and frames at 60 mph. Windows that were adequate when they went in can start leaking air, fogging between panes, or letting water past the sill within a decade. We replace and install windows and doors across Dallas with products rated for this climate, not for a milder one. Every job gets a written price before anyone touches a frame, and our technicians have up to 19 years of experience on Texas homes. Call (833) 954-5327 and we’ll start with a free estimate.
What Our Windows & Doors Service Includes

Window Installation
New-construction and rough-opening window installation means framing the opening, flashing it correctly, and setting the unit so water sheds outward, not into the wall. You need this when you’re adding on, finishing a garage conversion, or replacing a window that was never framed right to begin with. We set each unit with a sill pan and proper flashing, then check the perimeter with a moisture meter before the trim goes back on. The photo record from that visit shows you the flashing before it’s covered.
Door Installation
Door installation covers exterior entry doors, interior doors, and the frames around them, and it’s the trade where a 1/8-inch error shows up as a draft or a sticking latch for years. You need it when a door has swelled, warped, or never closed squarely after settling. We plumb and shim every frame, seal the threshold, and hang the slab so the gap is even on all four sides. Entry doors get new weatherstripping and a sweep as standard, not an upsell.
Window Replacement
Replacement means pulling the old unit and setting a new one into the existing opening, usually as a retrofit or full-frame swap depending on the condition of the surrounding trim and sheathing. You need it when glass is fogged, frames are soft, or the unit no longer closes and latches. In older Dallas neighborhoods like Lakewood and Junius Heights, we often find the original single-pane sash set into a wall with no flashing at all, which is why the water damage shows up before the glass fails.
Impact Windows & Doors
Impact windows and doors use laminated glass and reinforced frames designed to resist wind-borne debris and stay in the opening under pressure. You need them on homes in hail-prone corridors and anywhere the insurance carrier asks for impact-rated openings. We install and replace impact assemblies from ES Windows and CGI, and we’ll tell you plainly when a standard unit will do the job and when it won’t. Impact rating is a spec on the label, and we show you that label.
Energy-Efficient Windows
Energy-efficient windows carry a low-e coating, an insulated glass unit, and a frame material chosen for thermal performance, all measured by U-factor and Solar Heat Gain Coefficient. You need them when west-facing rooms cook in August or the HVAC runs flat out to hold 74. In Dallas, a west-facing wall takes direct afternoon sun for four or five hours a day, and a low-SHGC glass on those openings makes a measurable difference. We match the glass spec to the orientation of each wall rather than ordering one unit for the whole house.
Sliding & Patio Doors
Sliding and patio doors are wide openings with a track, rollers, and a large glass panel, and they fail at the track and the seal long before the glass goes. You need a replacement when the door drags, the track is pitted, or water pools inside the threshold. We install impact sliding glass doors and standard sliders, level the track, and check drainage before we call it done. On homes in Plano and Richardson, we regularly see the original 1990s slider with a failed roller and a threshold that’s been leaking quietly for years.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Brands We Service for Windows & Doors
We install and service ES Windows products, and we know where they hold up and where they need attention. ES builds impact-rated assemblies with laminated glass and heavy frames, so the failure points tend to be the seals and hardware rather than the glass itself. When we open one up, we’re looking at the weatherstripping, the weep system, and the frame anchor pattern, not guessing. We also work with CGI windows and doors, and we’re familiar with how their impact lines are glazed and set, which matters when a replacement has to match an existing opening spec.
ECO Window Systems is another line we install and service, and we’ve learned its frame profiles well enough to source a matching unit when a single opening needs replacing without redoing the whole elevation. On the installation side, the brand matters less than the flashing, the shimming, and the seal, and we treat every unit the same way regardless of the label on the frame. Whether you have ES Windows, CGI, ECO Window Systems, or any other make, we can help, and we’ll tell you honestly whether a repair or a full replacement is the better spend.
Signs You Need Windows & Doors Right Now
- Fogging or condensation between the panes. That’s a failed seal on the insulated glass unit, and the glass can’t be dried out or resealed. It won’t fix itself, and the lost insulation shows up on your summer cooling bill.
- Drafts you can feel with the back of your hand. Run your hand along the frame on a windy day. A draft at the sash or the sill means failed weatherstripping or a frame that’s no longer square, and both let water in behind the air.
- Water staining or soft wood at the sill or threshold. Staining on interior trim under a window, or a threshold that’s spongy underfoot, means water has been getting past the flashing or seal for a while. In Dallas, that damage spreads fast once the rainy season starts.
- A door that sticks, drags, or won’t latch. A door that catches on the frame in humid weather is telling you the frame has moved or the hinges have sagged. Left alone, the gap widens and the seal fails.
- Condensation on the inside of the glass in cool weather. Interior condensation points to a glass or frame that’s no longer insulating, and it’s one of the clearest early signals that a unit is past its useful life.
Our Windows & Doors Process – Step by Step
- 1
Free estimate and written scope. We measure every opening, note the frame condition and the wall assembly, and hand you a flat written price with a written scope before any work is scheduled. Under Clause 1 of the Haven Standard, that number is written before anyone starts. If you have a competitor’s quote, we’ll review it line by line at no charge as a free second opinion.
- 2
Product selection with the spec in writing. We walk through glass type, frame material, and impact rating, and we put the exact spec on the quote so there’s nothing to argue about later. You’ll see the U-factor and SHGC numbers on the label, not just a brand name.
- 3
Removal and substrate inspection. Once the old unit comes out, we inspect the rough opening, the flashing, and the sheathing, and we photograph what we find. If the framing is soft or the flashing was never there, we document it and quote any added work in a signed change order before proceeding.
- 4
Installation and sealing. We set the unit level and plumb, flash the opening, seal the perimeter, and check the operation of every sash and latch. A moisture meter confirms the assembly is dry before the trim and finish go back on.
- 5
Walkthrough and documented photo record. We test every opening with you, hand over the written warranty and the photo record from the visit, and leave the work area clean. The record of what we found and what we did is part of the job, not an extra.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Windows & Doors Cost in Dallas?

Most Dallas window and door work lands in a few predictable ranges, and you deserve the number before you call. A typical impact window installation in Dallas runs $8,000 – $25,000 depending on how many openings, the glass spec, and the frame material. Standard window replacement runs $4,500 – $15,000 for a whole-house job or a smaller set of openings. Impact sliding glass doors and patio doors sit inside the impact range, with the count and width of the openings driving the number. Single-door installation and impact-rated entry doors are quoted per opening once we see the frame.
What moves the price: the number and size of openings, whether it’s a retrofit or a full-frame swap, the glass spec (impact, low-e, or both), and any hidden framing or flashing repair under the old unit. What keeps you from overpaying: getting the spec in writing, comparing line items rather than totals, and asking whether flashing and weatherstripping are included or billed separately. Our free estimate includes a written scope, a flat price, and a documented look at what’s actually behind the wall, so the number you agree to is the number you pay unless a signed change order says otherwise.
| Service | Typical Dallas Range |
|---|---|
| Impact Window Installation | $8,000 – $25,000 |
| Window Replacement | $4,500 – $15,000 |
| Impact Sliding Glass Doors | Quoted per opening, within impact range |
| Entry & Interior Door Installation | Quoted per opening after inspection |
Windows & Doors Near Dallas – Our Service Area
We work across Dallas and the surrounding cities, including Garland, Richardson, Rowlett, Sachse, Murphy, Sunnyvale, Hutchins, Seagoville, and Balch Springs. Response times depend on the day, and we’ll give you a realistic window when you call rather than a promise we can’t keep. If you’re outside the core, start with our Dallas service area page, or check the Mesquite service area and Balch Springs service area pages for nearby coverage. Wherever you are, the estimate is free and the price is written before work starts.
Serving Dallas, TX – Our Local Coverage Area
We serve Dallas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Windows & Doors in Dallas

It covers window installation, door installation, window replacement, impact windows and doors, energy-efficient windows, and sliding and patio doors, including impact sliding glass doors. We handle the whole opening: removal, inspection, flashing, setting, sealing, and the finish trim. If a job needs framing repair behind the wall, we document it and quote it in a signed change order before proceeding.
A single door usually takes part of a day, and a full-house window replacement typically runs one to three days depending on the number of openings and whether any framing repair turns up. We give you a realistic schedule with the written quote, and we don’t promise same-day turnaround on planned work. If we find hidden damage, the change order tells you how much time it adds before we start.
Window replacement in Dallas runs $4,500 – $15,000 for most homes, and impact window installation runs $8,000 – $25,000 depending on the count and glass spec. The variables are the number and size of openings, the frame material, and any hidden repair. Call (833) 954-5327 for an exact quote, because estimates are free and the written price comes before any work starts.
Yes. We install and service ES Windows, CGI, and ECO Window Systems, and we know each line’s frame profiles and common wear points. Whether you have one of those or another make, we can help. The brand matters less than how the unit is set and sealed, and we treat the installation the same way regardless of the label.
We answer the phone 24/7 with a live person, so call and we’ll tell you what’s realistic for your situation. For a broken pane or a door that won’t secure, we can talk through a temporary measure while a repair is scheduled. Planned replacements are scheduled, not rushed, because a rushed installation is how flashing gets skipped.
Every job carries the 365-Day Done Right Promise: if it isn’t done right, we make it right. The warranty is written on the quote and backed by a terms page, not an asterisk. You also get a documented photo record from the visit, so you know exactly what was found and what was done.
Clear a path to each opening and move anything breakable away from the work area, and plan for some dust and noise on removal days. We protect the floors and cover the openings as we go, and the crew is background-checked and uniformed. If you have pets, a closed room away from the work keeps them calm and out of the way.
Schedule Your Windows & Doors Service in Dallas Today
Call (833) 954-5327 to schedule a free estimate on windows and doors in Dallas. We’ll measure every opening, show you the spec in writing, and hand you a flat price before any work begins. No obligation, no pressure, and a live person answers the phone 24/7. If you’re weighing a repair against a replacement, bring us a competitor’s quote and we’ll review it line by line at no charge.
Written by the team at Rowan Construction Group.












