







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterHow Much Does Walk-In Shower Installation Cost in Dallas?
A walk-in shower installation in Dallas typically costs $4,500 to $12,000, with most homeowners landing near $7,200 when they remove an old tub-and-surround unit and build a full tiled shower in its footprint. A straight shower replacement without moving plumbing runs $3,000 to $8,500, and a tub-to-shower conversion sits at $3,500 to $10,000. The number moves most on tile selection, glass, and whether we’re relocating the drain.
Before we go further, one thing this page won’t do: hand you “it depends.” Under Clause 1 of the Haven Standard, the written price comes before anyone starts. This guide gives you the Dallas line-item ranges so you can screenshot them, compare them against any quote you receive, and know in ten minutes whether a bid is honest.
Key Takeaways
- Most Dallas walk-in showers land between $4,500 and $12,000; full tiled custom builds with frameless glass hit the top of that range.
- Tile and glass account for roughly half the total. A $14-per-square-foot porcelain and a $45-per-square-foot marble are not the same project.
- Dallas clay soil and slab-on-grade construction mean shower pans get built correctly or they fail. A curbless, linear-drain shower requires a recessed slab or engineered subfloor, which adds $1,200 to $3,000.
- Permits are required in Dallas for plumbing relocation and drain moves. We pull them.
- Every Rowan project gets a flat written price, a written scope, a signed change order before any change, and a documented photo record on every visit. The 365-Day Done Right Promise is printed, not promised verbally.

Walk-In Shower Installation Cost Breakdown (2026)
The table below shows 2026 Dallas pricing for each phase of a walk-in shower installation. These are the ranges we use to build a written quote, and they hold across the trade.
| Line Item | Dallas Range (2026) |
|---|---|
| Demolition and haul-away (existing tub or shower) | $350 – $900 |
| Plumbing rough-in (drain relocation, valve, supply lines) | $600 – $2,400 |
| Shower pan / waterproofing membrane | $700 – $1,800 |
| Wall tile installation (labor, 40-60 sq ft) | $900 – $2,600 |
| Wall tile material (porcelain to marble) | $400 – $3,000 |
| Floor tile and drain tie-in | $300 – $900 |
| Glass enclosure (framed, semi-frameless, frameless) | $700 – $3,200 |
| Shower valve, head, handheld, and trim (Kohler or Moen) | $400 – $1,600 |
| Niche, bench, and built-in seat | $300 – $1,200 |
| Dallas permit and inspection | $150 – $400 |
| Finish work, paint touch-up, and clean-out | $150 – $450 |
| Total walk-in shower installation | $4,500 – $12,000 |
What separates a $5,200 job from an $11,400 job is rarely one line item. It’s usually three stacked together: marble or large-format tile that requires a certified installer and extra substrate work, a curbless design with linear drain, and a frameless glass door in a wider opening. The shower valve itself moves the number further than most homeowners expect – a simple Kohler pressure-balance line runs a few hundred dollars, while a thermostatic system with multiple outlets can add well over a thousand.
If you’re scoping a shower as part of a broader bathroom project, the full Rowan service overview covers how showers, vanities, and fixture work price together. A full bathroom remodel runs $9,000 to $28,000, and small bathrooms run $5,000 to $12,000 – often the shower install shifts the total less than people think once the floor and vanity are already being touched.
What Affects Walk-In Shower Installation Pricing in Dallas
Six factors move a Dallas shower estimate more than anything else. We’ve broken each down with the specific range.
- Shower size and layout. A standard 36×48-inch alcove shower is the cheapest footprint. A 48×60-inch walk-in with a wide entry adds $400 to $1,200 in material and labor, and a full walk-behind design with bench can push past that.
- Tile selection. Porcelain starts around $4 to $12 per square foot. Ceramic runs cheaper but chips at cut edges. Natural stone – marble, travertine, slate – starts at $15 per square foot and climbs well past $40. Large-format tile (12×24 or 24×48) is the sweet spot for a clean look that still installs efficiently, but it requires a dead-flat substrate and a more experienced setter. Expect an extra $600 to $1,500 across the job.
- Glass enclosure type. A framed sliding door is $700 to $1,200. Semi-frameless runs $1,200 to $1,900. Frameless is $1,900 to $3,200 and requires the opening to be square within 1/8 inch – which means the framing has to be right before tile goes up.
- Curb vs. curbless. A curbless shower with a linear drain is the modern Dallas look, but the slab has to be recessed or a bonded mud bed has to be engineered around it. That’s an extra $1,200 to $3,000 for the structural work, drainage, and waterproofing coordination.
- Plumbing relocation. Keeping the drain where it is saves $400 to $1,200. Moving the drain six inches or more in a slab-on-grade Dallas home usually means concrete cutting and re-pour. In pier-and-beam homes in Old East Dallas or parts of Oak Cliff, it’s a completely different scope – and easier.
- Wall and substrate condition. We regularly find rot behind shower walls in older Dallas homes – particularly in mid-century construction where original furring strips were never treated. In those jobs, reframing and moisture-resistant substrate add $400 to $1,400. We photograph what we find and explain it before any change order is written.
Dallas-Specific Cost Drivers
Dallas has a few complications that other markets don’t. Slab-on-grade is standard across most of the metro, which means any plan to recess the shower floor for a curbless design runs into post-tensioned concrete in newer builds – and cutting a post-tensioned slab without an engineer’s sign-off is not optional. We coordinate that step when it applies.
Our soil expands and contracts with the blackland clay content, especially between the wet spring and the dry Augusts. That movement shows up in shower floors as hairline cracks in tile or grout popping at the perimeter. A correctly built shower pan with a bonded membrane and proper slope-to-drain tolerates more of that movement than the original builder-grade pan ever did. If you’re seeing grout failure now, that’s a sign the pan or the waterproofing layer under it has been compromised – and it usually means pulling the floor, not patching it.
Water quality matters too. Dallas water runs hard, and shower heads, valves, and trim fixtures that aren’t rated for it scale faster. We lean toward Kohler and Moen valves with high-temperature ceramic cartridges – they tolerate hard water better than the cheaper thermostatic cores and cost less to rebuild in five years.

How to Save on Walk-In Shower Installation
You can cut $1,500 to $3,000 off a Dallas walk-in shower without compromising the parts that matter. Here’s how we see homeowners do it.
- Keep the plumbing where it is. Working with the existing drain location saves $400 to $1,200 and skips the permit-heavy scope change. If you don’t need the shower door to move, don’t move it.
- Porcelain over natural stone. A well-chosen 24×24 porcelain tile looks like stone and costs a third of it. The savings on a 60-square-foot shower are $800 to $2,500.
- Framed or semi-frameless glass over frameless. Semi-frameless reads clean and saves $700 to $1,300. It’s also more forgiving of minor wall variation.
- Skip the built-in bench in small showers. A bench costs $300 to $1,200. A tile-corner or freestanding stool gets you the function for far less, and small showers feel bigger without one.
- Bundle with other bathroom work. If the floor tile, vanity, or lighting is already being touched, a shower install adds far less than a standalone job. The Dallas service area page shows how we quote multi-scope bathroom work with one flat written price rather than three separate trades.
- Get a written price first, always. Clause 1 of the Haven Standard is the whole point: no work proceeds until the price is written, and no change proceeds until the change order is signed. Projects finish within a few percent of the number you agreed to because the number was real when it was written.
We also offer a free second opinion on any written estimate. Bring a competitor’s quote and we’ll review it line by line at no charge – whether or not you hire us. Homeowners who’ve already collected one bid usually come out ahead by having a second set of eyes catch what the first bid left out. Call (833) 954-5327 for a written estimate before work starts.
Repair or Replace? When a New Walk-In Shower Makes Sense
A shower that’s leaking will usually cost more to repair properly than to replace. If the membrane under the pan has failed – which is what’s happening when you see loose tile or weeping at the curb – the repair scope is the shower. That said, replacing a shower valve or a piece of trim is a $200 to $800 job. Cracked tile in one spot is $100 to $300, which is worth doing if the pan is sound. But if you’re seeing the third grout crack in two years, or the pan has ever leaked into the ceiling below, replacement is the honest answer. A repair that doesn’t fix the waterproofing just delays the same call.
FAQs – Walk-In Shower Installation Cost
How much does a walk-in shower installation cost in Dallas?
Walk-in shower installation in Dallas costs $4,500 to $12,000 in 2026. A straight swap without moving plumbing runs $3,000 to $8,500. A full tiled shower with frameless glass and a custom tile design lands at the top of the range. Call (833) 954-5327 for a written price based on your actual bathroom – free estimate, no obligation.
Is a walk-in shower cheaper than a tub-to-shower conversion?
No. A tub-to-shower conversion costs $3,500 to $10,000, and it’s typically cheaper than a from-scratch walk-in shower install because the drain and valve are usually reused. A conversion removes the tub and builds the shower in its footprint. A new walk-in shower install, especially a curbless one, costs more because the pan and drainage often have to be engineered from scratch. Call (833) 954-5327 for an honest comparison on your specific bathroom.
Do I need a permit to install a walk-in shower in Dallas?
Yes, for any plumbing relocation or drain change – Dallas requires a plumbing permit and an inspection for that work. Cosmetic tile replacement on an existing shower doesn’t always need a permit, but moving the drain or valve does, and the inspection is what protects you if the pan leaks later. Permit fees typically add $150 to $400. We pull the permit and schedule the inspection. Call (833) 954-5327 to talk through your scope.
How long does walk-in shower installation take in Dallas?
Most Dallas walk-in shower installs take 4 to 8 working days once materials arrive. A simple alcove tile shower runs 4 to 5 days. A custom build with a curbless pan, frameless glass, bench, and large-format tile runs 7 to 10. Glass fabrication typically adds 5 to 10 days to the schedule on its own – measure that into your expectations before demo starts. Call (833) 954-5327 for a written schedule with the estimate.
Can you install a walk-in shower in a post-tensioned slab home?
Yes, but any recess for a curbless design requires engineering. Dallas homes built after roughly 1985 often sit on post-tensioned slabs, and cutting into one without an engineer’s sign-off is a real risk of structural failure. For those homes we typically build a low curb instead of recessing the slab, or we coordinate with a structural engineer. The engineering and coordination adds $600 to $1,800. Call (833) 954-5327 to walk through the options for your home.
What brands do you use for shower fixtures and tile?
Kohler and Moen for valves, shower heads, and trim – both hold up better than builder-grade in Dallas’s hard water. Tile comes from our vetted tile suppliers, and we source through a network of more than fifty brands across the trades, including Kohler, Moen, and stockists for large-format porcelain and natural stone. Every brand and model appears in the written scope before work starts. Call (833) 954-5327 to talk through material choices and what each one does to the number.
What does the 365-Day Done Right Promise cover?
Every walk-in shower install comes under the 365-Day Done Right Promise: if it’s not done right, we make it right. That’s backed by the Haven Standard and printed on every page and in every written scope. It covers workmanship and materials installed by our crews for one full year. Our technicians have up to 19 years of experience with tile, waterproofing, and shower construction in Dallas homes. Call (833) 954-5327 for the full terms and a written quote.
What the Written Quote Includes
Every Rowan quote is a flat price with a written scope and a written warranty. No “call for a quote,” no verbal ballpark, no numbers summoned on the hood of a truck. By the time you receive an estimate, you’ll have a document that names the tile, the valve, the glass type, the membrane system, and the timeline – dollar for dollar. If anything changes mid-project, it doesn’t move until a change order is signed. That’s the discipline that has kept our projects within a few percent of the agreed cost across 4,000-plus jobs.
Every visit also includes a documented photo record – not an add-on. You’ll have images of the substrate condition, the waterproofing layer, the tile work as it went up, and the finished shower before the crew leaves. If something goes wrong two years out, you have documentation of what was underneath the surface, not just what was visible.
Why Dallas Homeowners Ask for the Second Opinion
Most of our walk-in shower customers in Dallas already have one bid before they call us. They research contractors the way they research appliances – reading the three-star reviews, checking what’s excluded, comparing what’s in the scope. Bring a competitor’s written estimate and we’ll review it line by line at no charge, whether or not we end up doing the work. We’d rather you see the difference in writing than hear it from us.
Estimates are free. A live person answers the phone, and you’ll receive a written price before any work starts. Call (833) 954-5327 to schedule your walk-in shower estimate and get the number in writing.
Pricing reflects the Dallas market as of 2026. Rowan Construction Group Dallas offers free estimates – call (833) 954-5327.
Written by the team at Rowan Construction Group.
What Our Customers Say
"They found an old septic line under the driveway run and stopped, documented it, and re-quoted before continuing."
- Xavier L."Final invoice was within two percent of the contract. Every change was priced and signed before anyone picked up a tool."
- Malcolm T."Driveway replaced properly with a base that will actually last. They explained why the cheaper quote was cheaper."
- Reggie O.












